Backflow Assembly Repair in Ontario

Rebuilding failed backflow assemblies, then retesting and filing the result.

Assembly repair usually means taking the device apart, cleaning out debris, replacing worn rubber parts and putting it back together. Then we run the full test again. If it passes, the report goes to your district.

  • PriceFree quote
  • Time1–2 hours
  • RetestIncluded
  • ApprovalPrice first

Want to get on the schedule? Call or book online.

How the repair goes

  • Test again and send the report
  • Replace worn parts
  • Find which part failed
  • Take the assembly apart
  • Quote the fix

Reading the failed test

The failed readings point to the problem. They show whether it's the first check, the second, the relief valve on an RP or the air inlet on a vacuum breaker.

Knowing that keeps the repair targeted. We open the failed section and look for the cause, usually debris, worn or cracked rubber, a tired spring or a torn diaphragm.

If another company tested your device, the readings are on their report. Send it over and we'll bring the right parts, which usually means a single visit.

Inside the repair visit

With the readings in hand and your approval on the price, we shut off the water to the device. Depending on the setup, that may mean the whole property or just one line, like irrigation or the fire service.

We open the failed section, remove the internal parts and clean the seats. Worn rubber, springs or diaphragms are replaced with the manufacturer's parts. The body is checked for cracks and the shutoff valves for leaks.

Then the assembly goes back together and the water comes back on. Most repairs take 30 minutes to an hour of water downtime. On a busy business, we can often schedule around your hours.

Retest and filing

A repair isn't finished until the device passes again. Right after reassembly, we run the full test, the same procedure used on the annual test. If everything holds, the result is recorded as a pass after repair, along with the parts replaced.

We file that report with your water district so your device shows as compliant. You get a copy by email.

If the retest still shows a problem, we keep working until it passes or tell you why it won't. Sometimes a device that's had several repairs, or one with damage to the body, is better off replaced. We'll give you the numbers so you can decide.

How we decide whether to fix it

Most failed assemblies are worth repairing. A rebuild kit costs much less than a new device, and a rebuilt assembly can pass for years.

Replacement starts to make sense when the body is cracked, when the device is so old that parts are no longer made, when it's been repaired several years in a row, or when it's the wrong type for the hazard. Sometimes the district requires an upgrade, such as moving from a double check to an RP after a change of use.

We'll give you a straight answer on which makes more sense for your device, with prices for both when it's close. The choice is yours.

Keeping it from failing again

When the same device keeps failing from debris, look upstream. Main breaks, nearby construction and aging pipe can push grit into the line.

A strainer before the device sometimes helps, but districts don't always allow it and it needs regular cleaning. If we suspect an upstream cause, we'll explain it and lay out the options.

Working around your hours

Shutting off water at a restaurant at noon or a clinic during appointments isn't an option. For businesses, we schedule repairs around your hours, early mornings, late afternoons or slower days.

Let us know when water can be off and for how long. We'll plan the repair to fit, and the retest and filing happen before we leave.

Repair pricing explained

Pricing depends on the size of the assembly, which part failed and which parts it needs. A small home device kit costs far less than rebuilding a large fire line assembly.

The quote you approve covers parts, labor, the retest and the district filing. If a new device would cost roughly the same, we'll mention it so you can choose.

Managers can have us send the quote directly to the owner or board. Once it's approved, we do the repair, file the passing report and email a copy to everyone who needs one.

How long is the water off?

Most repairs keep water off for under an hour. We'll give you a heads up first.

Questions

What if parts aren't on the truck?

We order them and come back. Most parts arrive within a few days.

Do you quote before starting?

Always. You approve the price before we open the assembly.

How long does an assembly repair take?

Most are done in one to two hours, including the retest.

Can you repair it the same day as the test?

Often, yes, if we have the parts on the truck. Otherwise we order them and come back.

Can you repair it if someone else tested it?

Yes. Send us the failed readings and we'll quote the repair.

Will the report show it failed first?

Yes. Districts expect the report to show the initial result and the passing retest after repair.

What to expect when you book backflow assembly repair

Booking takes a couple of minutes by phone or online. We confirm the address, the device and how to reach it, and we'll give you a time window that works for you. For most homes, you don't need to be there.

On the visit, a certified tester does the work with a calibrated gauge and explains anything that comes up in plain terms. If a repair is needed, you'll get the price before anything happens. When the device passes, we send the report to your water district and email you a copy. Our office is open seven days a week, 6am to 12pm, and emergency calls are answered around the clock.

Backflow Assembly Repair in Ontario and nearby

Need backflow Assembly Repair outside Ontario? We also cover Upland, Montclair, Chino, Rancho Cucamonga and Pomona. Same-week visits are normal, and booking takes a couple of minutes.

Have a notice from your district?

Same-week appointments. We handle the paperwork.

Call NowSchedule