Backflow Installation in Ontario

The right backflow preventer for your property, installed to code, tested and certified.

A new installation starts with knowing what your district requires. From there we install the device, test it, and submit the report so your annual cycle starts clean.

  • PriceFree quote
  • TimeUsually 1 day
  • TestIncluded
  • FilingIncluded

How it works

  1. Site visit

    We confirm type and size.
  2. Approvals

    Permits if needed.
  3. Install

    Usually one day.
  4. Test & file

    Report sent to your district.

Want to get on the schedule? Call or book online.

Backflow Installation by The Backflow Testers of Ontario

Who usually needs a new device

  • New building or new water service
  • New irrigation system
  • New tenant or change of use
  • Your water district says one is required

Which device your property needs

The first step is knowing what your district requires. The hazard at the connection sets the type: RPs for high-hazard uses such as clinics and car washes, double checks for many lower-hazard lines, and PVBs or SVBs for irrigation exposed only to backsiphonage.

Then we size it. Too small and you lose pressure. Too large and you pay more for no benefit. Homes typically take 3/4-inch or 1-inch devices, and commercial and fire lines often need 2 inches or more.

Choosing correctly up front saves you from a costly redo if the district turns the first device down.

Built for easy testing and repair

Every device we install will need a test each year and the occasional repair, so access and placement matter from day one.

RPs stay above grade so the relief valve can drain. PVBs and SVBs go above the highest sprinkler or outlet. We leave room around each device for gauges, valve handles and check covers.

If the location is exposed to theft or cold, we'll recommend a cage or cover. A well-placed device passes its first test and stays simple to service.

From quote to first report

It starts with a visit or a few photos so we can confirm the connection, hazard and space. You get a free quote that includes the device, the installation and the first test.

If the district or city needs plans or a permit, we'll tell you upfront and build it into the timeline. Most residential and small commercial installs are done in a day.

Once the device is in and the line is flushed, we test it and file the first report with your water district. That puts it on record and sets the first annual due date. You get a copy, and we can remind you when next year's test is coming up.

New devices at houses

Homes usually need a new device for sprinklers, pool fill lines, wells or residential fire sprinklers. Most are 3/4 inch or 1 inch and go in within a day.

We choose a location that follows the placement rules and stays accessible for testing, then test it and send in the first report.

Commercial and new construction

Business and construction projects tend to need plans, permits, bigger devices and coordination with other trades. Fire services commonly use detector assemblies 4 inches and larger.

We fit into your project timeline and file the startup test before final inspection.

Changing how a property uses water

Adding a new boiler, a fertilizer injector, a car wash bay or medical equipment can change the hazard level at a connection. So can converting a space from one kind of business to another. When that happens, the district may require a new or different backflow device.

If you're planning a change like this, call before the work starts. Getting the right device in the plan from the beginning is cheaper than adding it after an inspection flags it.

Not sure whether you need a new device at all? Send us a photo of the area and a short description of the project. We'll tell you whether a backflow device is likely required, what type and roughly what it would take, before you commit to anything. Quotes are free, and most homes and small businesses are done in a single day.

Our backflow installation services in Ontario

Backflow Preventer Installation

We figure out which preventer your property needs, RP, double check, PVB or SVB, based on the hazard and your district's rules. Then we size it, install it and certify it with the first test. You get a free quote before any work. Most homes and small businesses are done in a single day. More about backflow preventer installation.

Backflow Assembly Installation

Proper placement on every assembly we install: above grade where required, high enough to work, and with room to test and repair. We add theft or freeze protection when it makes sense, then test the device and file the first report for you. Moving an existing assembly? We do that too, with a retest afterward. More about backflow assembly installation.

Questions

Which type do I need?

Your water district decides based on how the water is used. We confirm it before we quote.

How often do I need a backflow test?

Once a year at minimum. A device also needs testing right after it's installed, repaired or moved. Your water district picks the due date and normally mails a reminder ahead of time.

How we handle backflow installation in Ontario

Our approach is simple. Show up when we say we will, do the work right, and handle the paperwork so you don't have to. Every tester is certified, every gauge is kept in calibration, and filing with your water district is included.

Pricing is clear. Tests are a flat $105 for devices under 4 inches and $175 for 4 inches and larger, and anything beyond the test is quoted before we start. We're available seven days a week from 6am to 12pm, with emergency calls answered 24/7. Most Ontario appointments are within the same week, and you'll have a copy of your report by email when we're done.

Where we offer Backflow Installation

Our testers handle backflow Installation across Ontario and the surrounding area, from Upland, Montclair, Chino, Rancho Cucamonga and Pomona. Call for the next opening or schedule online.

Have a notice from your district?

Same-week appointments. We handle the paperwork.

Call NowSchedule